MacBook Pro 13 2015 MagSafe 2 I/O Board (A1502 Replacement Genuine) — quick answer
The MacBook Pro 13 2015 MagSafe 2 I/O Board (A1502 Replacement Genuine) is a replacement Apple DC power jack with pre-attached cable harness available at N.N Laptops, Hafeez Center, Lahore for Rs. 4,500. It's the OEM-spec MagSafe 2 magnetic charging board female jack for MacBook Pro 13 Retina 2014 A1502, MacBook Pro 13 Retina 2015 A1502. Plug-in installation (no soldering on the cable side), backed by our 30-day check warranty and nationwide.
Full specifications
| Brand | Apple |
|---|---|
| Connector Type | MagSafe 2 magnetic charging board |
| Cable Length | ~6-8cm pigtail with motherboard connector |
| Compatible Models | MacBook Pro 13 Retina 2014 A1502, MacBook Pro 13 Retina 2015 A1502 |
| Installation | Plug-in (no soldering on harness side) |
| Condition | Genuine — New service part |
| Warranty | 30-day check warranty |
Compatibility — which laptops does this DC jack fit?
This MagSafe 2 magnetic charging board female DC jack with pre-attached cable harness fits:
- MacBook Pro 13 Retina 2014 A1502
- MacBook Pro 13 Retina 2015 A1502
Match the connector type on your existing charger before ordering. If your laptop charges via a MagSafe 2 magnetic charging board barrel, this part is the correct fit — no other variant of jack will physically mate with the OEM charger.
Common DC jack failure symptoms
If any of these match your laptop, the jack is the likely culprit:
- Charger LED is on, but laptop only charges if you wiggle the cable at a specific angle
- Battery indicator on screen flickers between 'charging' and 'not charging' randomly
- You feel the jack move when you push on the charger plug
- The plug feels loose; the connection isn't snug like it used to be
- Charging suddenly cuts out when you bump the laptop
If two or more of these match, the internal jack solder pads have likely cracked from years of plug-in / plug-out stress. Replacing the harness is a permanent fix.
Installation — step by step
Most modern laptops use a cable-harness jack like this one (rather than a board-soldered jack), so installation is screwdriver-only:
- Power off laptop, remove AC and battery
- Unscrew bottom panel (8-12 Phillips, sometimes Torx T5)
- Locate old DC jack pigtail connector on motherboard
- Unlatch ribbon / unplug 2-pin connector
- Remove old jack from chassis (1-2 screws, sometimes glued — gently pry)
- Seat new jack into the same recess, screw down
- Plug new harness into motherboard connector
- Reassemble, test with charger before fully closing
Total time: 20-30 minutes for someone comfortable with laptop teardown. We do free installation in shop if you bring the laptop to Hafeez Center.
Build quality & why we sell this specific part
OEM-grade plastic body with proper metal contacts for the centre-pin and outer-barrel return. The wire harness uses heavier 22 AWG copper than no-name aftermarket parts — important because a MacBook Pro 13 Retina 2014 A1502 charger draws up to 4-6A and thinner copper would heat up under load. The motherboard-side connector is the correct keyed JST type, so it only fits one way and you can't reverse it.
Where to buy in Lahore
Visit us at Shop 66A, 3rd Floor, Hafeez Center, Gulberg III, Lahore. We stock dozens of jack variants — bring your laptop or the old jack and we'll match it instantly. Lahore delivery, nationwide via TCS / Leopards. WhatsApp 0314 4000131 for stock confirmation.
Browse our full laptop parts, laptop chargers, laptop batteries selection.
Warranty
Every DC jack carries our 30-day check warranty. If the jack fails on install, develops loose contact within 30 days, or causes intermittent charging, return it to the shop with the invoice for a full replacement. No questions asked within the warranty window.
Frequently asked questions
Is the cable harness already attached?
Yes. The jack ships with a 6-8cm wire pigtail pre-soldered to the jack and terminated with the small 2-pin or 4-pin motherboard connector — just plug it into the board, no soldering required for the harness side.
Does this fit the MacBook Pro 13 Retina 2014 A1502?
Yes — this exact jack matches the OEM part number and connector size for the MacBook Pro 13 Retina 2014 A1502, MacBook Pro 13 Retina 2015 A1502. We've sold dozens of these to repair shops across Lahore. If you're unsure, send us a photo of your old jack on WhatsApp 0314 4000131 and we'll verify before you order.
Do I need a soldering iron to install this?
Only if you're replacing the older type that's directly soldered to the motherboard pads. Most modern Dell, HP and Lenovo machines now use a removable cable-harness jack like this one — pop the old harness out of its motherboard connector, plug the new one in. Five-minute job with a screwdriver.
Will the charger plug feel loose or work intermittently after I install this jack?
If the new jack is seated correctly on the motherboard and the solder joints are clean, the plug should feel firm — no wobble, no flicker. A loose-feeling charger after replacement usually means a cold solder joint on one of the four mounting pads.
Why choose this exact MagSafe 2 I/O Board over cheaper alternatives?
Many third-party DC jacks use thinner wires and lower-grade plastic that can deform over time, leading to poor contact. This genuine Apple service part uses heavy-duty 22 AWG copper wiring and high-temperature nylon connector housing, exactly as specified for the MacBook Pro 13 Retina (2014/2015 A1502). At Rs. 4,799, this MacBook Pro 13 2015 MagSafe 2 I/O Board (A1502 Replacement Genuine) remains one of the best-value genuine replacement parts in Pakistan for 2026, especially considering the rising cost of even basic laptop repairs. It's the same part Apple uses in their authorized service centers — we source it directly from Apple's supply chain, so you get factory-grade reliability without the premium markup. Every board is quality-checked at nnlaptops.com before listing, and we back it with a 30-day check warranty. If you're in Lahore, Karachi, Islamabad, Rawalpindi, Faisalabad, Multan, Peshawar, or Sialkot, you can get same-day Lahore delivery or nationwide shipping via TCS / Leopards — just WhatsApp Sayam at 0314 4000131 to confirm stock and arrange delivery.
Real-world performance and reliability
We bench-test every I/O board before dispatch to ensure consistent charging current and proper MagSafe 2 alignment. Customers from Karachi, Islamabad, Rawalpindi, Faisalabad and Multan have reported flawless charging after replacement. The board's pre-attached cable harness matches the original part number, so you get the same fit and function as the factory-installed piece. The connector is keyed to prevent reverse polarity, and the spring-loaded center pin provides a firm, wobble-free connection that lasts for years. Unlike some aftermarket boards that may cause the charger to heat up or charge slowly, this genuine Apple board delivers the full 60W power your MacBook Pro expects.
Shipping and availability across Pakistan
We offer same-day delivery within Lahore for orders placed before 5 PM — just message Sayam on WhatsApp 0314 4000131. For customers in Rawalpindi, Islamabad, Faisalabad, Multan, Peshawar, Sialkot, and other cities, we ship via TCS or Leopards courier with full tracking. The price of Rs. 4,799 includes the board and connector harness; no extra charges for the part itself. We maintain a large stock at Hafeez Center, Gulberg III, Lahore, so out-of-stock situations are rare. If you need this part urgently, walk in to Shop 66A, 3rd Floor — we'll have it ready for you. For online orders, simply contact Sayam via WhatsApp, and he'll guide you through the process. Visit nnlaptops.com for more laptop parts.
N.N Laptops — Shop 66A, 3rd Floor, Hafeez Center, Gulberg III, Lahore. WhatsApp / Call 0314 4000131. Lahore delivery, nationwide via TCS / Leopards, 30-day check warranty.
